Request A Quote

 

Every person may have their unique concepts about How to Install a Bathtub Yourself.

Setting up a bathtub isn't specifically brain surgery, however it does need strong plumbing, woodworking, as well as in some cases, tiling skills. Replacing an old tub with a brand-new one is additionally a reasonably hard task. If the old bathtub is easily obtainable, the task can relocate immediately; if you have to open a wall to eliminate the old bathtub as well as position the new bath tub, the job is a lot harder. In either situation, the task is within a home handyman's skills, although you will require a helper to leave the old bathtub and set in the new one. Make certain you have certified on your own for the work and also fit trying it. Rather than hiring a professional to take over a halfway-completed project, it is better to take into consideration utilizing one prior to you start. Possibilities are you may require a specialist plumber to make tube links.
This post will aid you install a brand-new tub in your bathroom if you have currently bought a new tub and do not require to transform the arrangement of your previous supply of water pipelines.
Your tools and also material checklist must consist of the following:

 

• New Tub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Level


• Pliers


• Flexible Wrench


• Putty Blade


• Screwdriver


• Cold Chisel


• Measuring tape


• Pipe Caps


 

Planning for the Setup

Firstly, the supporting frame supplied with the bath ought to be fitted (if required) according to the producer's directions. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is very important to see to it that if the tap includes a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bath, it is likewise practical to fit a supporting plate under the taps unit to avoid stress on the bathtub.
Fit the flexible faucet connectors to the bottom of the two taps making use of 2 nuts and olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet with the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. Ensure you utilize all of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom need to now be ready to be fitted in its final position.

 

 

Removing Old Taps

If you need to change old faucets with brand-new ones as a part of your installment, after that the first thing you ought to do is separate the supply of water. After doing so, switch on the faucets to drain any type of water remaining in the system. The procedure of removing the existing taps can be rather bothersome due to the restricted accessibility that is frequently the case.
Make use of a container wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipes to the faucets. Have a cloth ready for the remaining water that will certainly come from the pipelines. As soon as the supply pipes have actually been gotten rid of, make use of the same tool to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the single taps from turning throughout this procedure. When the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleansed of any old sealing substance.
Prior to going on to fit the brand-new taps, compare the pipeline connections on the old faucets to the brand-new faucets. If the old faucets are longer than the new taps, after that a shank adapter is needed for the brand-new taps to fit.

 

 

Installing the Bathtub

Using both wooden boards under its feet, place the bath tub in the needed placement. The wood boards are useful in evenly spreading out the weight of the tub over the location of the boards rather than concentrating all the weight onto 4 small factors.
The next objective is to make sure that the bathtub is leveled all round. This can be achieved by examining the level as well as readjusting the feet on the bathtub up until the level checks out degree.
To mount faucets, fit all-time low of the outermost adaptable tap adapter to the appropriate supply pipeline by making a compression sign up with; then do the very same for the various other faucet.
Switch on the water as well as examine all joints and also brand-new pipework for leaks and tighten them if essential. Load the tub as well as likewise examine the overflow outlet and also the normal outlet for leaks.
Finally, repair the bath paneling as defined in the maker's instruction manual. Tiling as well as securing around the bathtub needs to wait up until the bathtub has been utilized at the very least once as this will certainly settle it into its final setting.

 

 

Fitting New Touches

If the tails of the brand-new taps are plastic, after that you will certainly need a plastic port to prevent damages to the string. One end of the adapter fits on the plastic tail of the tap and also the various other end provides a link to the current supply pipes.
If you need to fit a monobloc, after that you will certainly need minimizing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, position the tap in the mounting opening in the bath/basin making sure that the washing machines are in place between the tap as well as the sink. Secure the tap in position with the manufacturer supplied backnut. As soon as the faucet is securely in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with normal tap ports. The previous type needs to be linked to the tap finishes initially, tightening just by hand. The supply pipelines can later on be attached to the other end. Tighten both ends with a spanner after both ends have been attached.

 

 

Tiling Around the Bath tub

In the location where the bathroom fulfills the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is very important as the installation can relocate sufficient to break an inflexible seal, creating the water to pass through the wall surface in between the bathroom as well as the tiling, causing problems with dampness and feasible leaks to the ceiling below.
You can select from a variety of coloured sealers to assimilate your fixtures and fittings. They are offered in tubes and also cartridges, and also can sealing voids up to a width of 3mm (1/8 inch). If you have a bigger gap to fill, you can load it with twists of soaked paper or soft rope. Bear in mind to constantly fill up the bath tub with water before securing, to permit the activity experienced when the tub is in usage. The sealer can fracture fairly very early if you do not consider this movement prior to securing.
Additionally, ceramic coving or quadrant tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also easily offered on the market. It is suggested to fit the ceramic tiles using water-resistant or waterproof sticky as well as cement.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

I'm just very enthusiastic about How to Install a Bathtub and I am praying you enjoyed our blog posting. Please take the opportunity to share this entry if you enjoyed it. I am grateful for your time. Please check up our blog back soon.

Request immediate service.